Pack 89's
PUBLIC SITE
Home Page
Car Derby Rules
Online Books
Boat Rules
Rocket Rules
Popcorn
Forms
Camps
Google Calender
Definitions
Camping Rules Info
About the uniform
Patch Placement
Websites
Leadership


 
Cub Scout Pack 89
(Kennett, Missouri)
 
ScoutLander Contact Our Pack Member Login
  
 

Rocket Rules



Space Derby Rules

All rockets must pass the following inspection to qualify for the race:

1. Only basic materials supplied in the Official BSA kit may be used. The hanging device supplied in the kit must be used.

2. The nose cone (propeller assembly) must not be glued in place on the nose of the rocket. A notch or groove should be formed in the tail of the rocket to seat the band holding dowel. The band holding dowel must not be glued in place. (These rules allow band replacement in case of breaks)

3. The rocket body may be no longer than 7 inches, not including the propeller and fins. Width 2.75 inches -Three rubber bands per rocket. Each Pack must supply extra rubber bands if the Pack should need them.

4. There are no restrictions on the weight or design of the rocket. Rockets may be detailed in any way as long as it does not exceed length restrictions, is flight worthy, structurally sound and does not interfere with another rocket during the race.

5. Rockets with wet paint will be disqualified

6. Scout shall use rocket built for this year, no previous year rockets will be allowed.

7.  Each ROCKET will be wound 100 times. Track will be 40 foot set up.

8.  Once the rocket is submitted for entry, no further adjustments can be made except in the case of mechanical failure.

9.  The race will be double elimination.

10. Any entry that experiences a mechanical failure will be allowed to re-race if it can be repaired during the same heat. It will count as a heat loss if it cannot be repaired prior to the   beginning of the next heat. All repairs of this type must be done with "Space Command" observing and certifying as to its flight worthiness.

11.  In the event that all rockets don’t reach the end of track, the one that goes the furthest is declared the winner.

12.  One Rocket Only per scout.

13. Racing volunteers are only allowed in the Space Track area.

14. No late registrations will be accepted after den has started the race

15. Racing will be conducted using the Lane Rotation Method

16. All rulings by “Space Command” are FINAL.

Note: All illegal rockets must be disqualified prior to racing.







Space Derby Procedure

  1. Every boy brings his rocket to the inspection table to have his entry checked and numbered.

    2. Then the scout goes to the registration table where his name and rocket's number are entered on a heat sheet.

    3. Contestants report to gatekeeper, who lines them up in the order in which they will compete. As the cub time approaches he will begin to wind his rocket.

  4. When the cub scouts name is called, he will hook his rocket on the guideline assigned to him.

  5. The gatekeeper releases the rockets.

  6. The winner takes his rocket to the registration table for recording. He then returns to the spectator area to wait until his name is called again.

PREFLIGHT INSPECTIONS

  1. Rockets are to be submitted to the registration table.

  2. Each rocket will be inspected, registered and assigned a sticker with a spacecraft number.

  3. After registration, rockets will be held by "Space Command" in the designated space hanger until race time.

  4. If at registration, a Rocket does not pass inspection, the owner will be informed of the reason for failure, and will be given time within the official registration period to  make the adjustment.

   5. The rocket you compete should be a new rocket, with a balsa wood body, not one built in a previous year.

Space Derby Pre-Race Check List

   1. Propeller is balanced. Sand if necessary.

     (Remember to learn the direction to spin propeller THIS SHOULD BLOW WIND TO THE REAR OF THE CRAFT)

    2. Propeller wire is as short as possible. Notch on propeller engages propeller wire securely.

    3. Rocket body is shaped as small as possible. FAST ROCKETS HAVE A MINIMUM PROFILE.

    4. Inside of body is hollowed out to reduce weight. If possible, select the lightest body you can obtain. LIGHTER ROCKETS GO FASTER.

    5. Plastic hanger is fastened securely to body.

    6. Groove for rear dowel is deep enough so dowel does not twist when rubber motor is wound tight

    7. Rubber bands have been tested to select the most powerful. Lubricate rubber bands in castor oil or a glycerin/soap mixture.

    8. Propeller nose button is lubricated with graphite.

     9. Rocket body is waxed to a high gloss to decrease wind resistance.

   10. Fins are accurately aligned so rocket flies straight.

   11. Rocket is balanced fore and after when a pin is inserted in rocket carrier hole.

Tips For Preparing for Flight

1.  Lubricate rubber bands before the derby. Lubrication prolongs the rubber bands life and power and will help reduce the possibility of their breaking during the competition They can be soaked overnight in castor oil.

2.  Each Pack are required to have extra boxes of rubber bands on hand. Remember, it takes three rubber bands to fly each ship properly.

3.  Experienced rocket racers "warm up" their space ships by gradually winding the rubber band motor to it full capacity.

4.  A small hand drill is excellent for winding rubber bands. It also helps speed up the event.

5.  For a more evenly matched race wind all rocket motors the same number of turns and that is 100 turns counter clockwise

6.  Reduce drag by making all surfaces smooth. A rounded nose causes less drag than a sharp nose. A good design has all leading edges rounded and trailing edges tapered to reduce air friction

7.  Rubber bands should be lubricated before the race. They are the motors and should be strong and flexible.

8.  The end with the small hole is the rocket nose.

9.  A potato peeler is good for carving the balsa wood.

10. To help increase the rocket's speed, reduce the weight. Do not weaken the area around the hanger or carve away the nose.

11. Do not apply to much paint to the outside.

12.  Make the propeller shaft as short as possible by bending it close to the prop. Cut off the excess wire with wire cutters.

13.  Test the rocket's balance. If the rocket is nose heavy, sand a little wood off that end. If it's tail heavy, remove wood from tail area.

SHAPING & CARVING THE ROCKET

1. -Reduce air friction or "drag" by making all surfaces as smooth as possible. A blunt, rounded nose causes less drag than a sharp nose. A good design has all leading edges rounded and trailing edges tapered to reduce the drag.

2. -Rocket body is shaped as small as possible. FAST ROCKETS HAVE A MINIMUM PROFILE.

3. -Inside of body is hollowed out to reduce weight. If possible, select the lightest body you can obtain. LIGHTER ROCKETS GO FASTER.

4. -Use a sharp knife for cutting the grooves for the hanger fitting and fins. A dull knife will crush and splinter the balsa wood. bullet When you start to carve, remember that the end with the small hose is the rocket nose.

5. - A new potato peeler is good for carving the shape.

6. -To help increase the rocket's speed reduce the wall thickness to a minimum of 1/8 inch. Do not weaken the area around the hanger (carrier) or carve away the nose button circle.

7. -Rocket is balanced before and after when a pin is inserted in rocket carrier hole.

8. -Plastic hanger is fastened securely to body.

9. -Groove for rear dowel is deep enough so dowel does not twist when rubber motor is wound tight.

MECHANICS OF THE ROCKET (PROPELLER ASSEMBLY)

1. -Do not glue the front nose/propeller assembly into the front of the space derby. It is pulled off to re-load new rubber bands!

2. -Do not glue the back dowel onto the rocket. It is pulled off to re-load new rubber bands!

3. -Propeller is balanced. Sand if necessary.

4. -Be careful not to get glue on the plastic carrier, especially in the holes through which the monofilament line runs. Glue can interfere with smooth operation.

5. - Make the propeller shaft as short as possible by bending it close to the prop. Cut off the excess wire with wire cutters.

6. -The propeller should have the rounded shaft-end pointing into (touching) the space derby (this makes the bending of the wire easier and it reduces friction).

7. -Propeller wire is as short as possible. Notch on propeller engages propeller wire securely.

8. -The little plastic straw MUST go over the hook (not just the shaft as the drawing in the space derby kit illustrates) This is where the rubber bands will hook on - the wire hook will cut the rubber bands without the plastic straw liner!!!

9. - The plastic dowel at the rear of the space derby to hold the rubber bands MUST be kept from rotating (groove out the back so the dowel can sit in it!) - do not glue it!

10. -Test the rocket's balance by hanging it from a string through the hole of the hanger fitting. If the rocket is nose-heavy, carve or sand a little wood off of the end. It it's tail-heavy, remove wood from the tail area.

11. -Propeller nose button is lubricated with graphite.

Rubber Bands

1. -Lubricate the rubber bands before the derby. This prolongs the bands' life and power and will help reduce the possibility of breaking during the competition. They can be soaked overnight in castor oil. Or mix two parts green soap, one part glycerin, and one part water and rub the mixture on the rubber band about an hour before racing.

2. -Have extra boxes of rubber bands on hand. Remember, it takes three rubber bands to fly each ship properly.

Experienced rocket racers "warm up" their space ships by gradually winding the rubber band motor numerous times before races (20 winds, then 40 winds, then 60, 80, 100) -- this helps relax the elastic properties of the band and makes it more pliable and durable (this is exactly why the clowns stretch the balloons before blowing them up!).

Winding Rubber Bands

1. -A small hand drill is excellent for winding rubber bands. It also helps speed up the event. Check the ratio of the drill by making one revolution of the crank handle and count the number of times the chuck turns. Most drills average a one-to-four ratio; thus it would take 40 turns of the crank to give 160 winds on the rubber band motor.

2. - When using the hand drill winder, it's best for one person to hold the rocket and propeller while another stretches the bands about 12 to 15 inches beyond the rocket tail and turns the rubber bands, he gradually shortens the distance between him and the rocket. bullet For a more evenly matched race, wind all rocket motors the same number of turns. For 100-foot launch lines, 150 to 170 winds should be sufficient.

Finish

1. - Painting and decorations are encouraged.